KRS Multilub PVT. LTD.

Radial Lubricator

KRS Multilub PVT. LTD. High Quality Tubes and Fittings are available in Steel tubes and Nylon tubes with 4/6 mm steel ends. With Colour Natural & Transparent (suitable for moving points). KRS Multilub PVT. LTD. High Quality Water cooled Tubes & Fittings

Model KRL-1.5-4 KRL-5-6 KRL-15-12 KRL-30-12 KRL-70-30
Reservoir Capicity in Kg. 1.5 5 15 30 70
No. of Outlets (Pump-Elements) 4 6 12 20 30
Motor 3Phase, 415V.AC, 4 Pole 0.25 HP 0.25 HP 0.50 HP 1.0 HP 1.50 HP
Delivery Pressure 200 kg/cm Square Maximim
Dose of Pump/Cycle (Adjustable) 0.05cc to 0.25cc/stroke/pump
Reduction Ratio of Drive 70:1

Manual Grease Pump

APPLICATION This pump meant for feeding grease to bearing & other moving part of machines & other lightly machines having 1to 20 lubrication point. WORKING On pulling the handle of pump, grease are sucked through suction port on pushing handle of pump grease comes out under pressure through check value. Spring pressure through follower plate exerted over the top surface of the grease further helps to push the grease in suction port. EQUIPMENT Pump is made up of purely transparent acrylic reservoir for storage of grease. For sensing the Grease level a tell tale rod is provide and follower plate assembly for help in positive suction of grease. It contains two outlet part of ¼” BSP right and left side in which one is used as air bleed valve and second port used as a outlet. To check reverse flow of grease, a non return valve is provide in the system at the outlet port. FILLING OF GREASE Grease can be filled manually or with another pump. Filling from pump ¼” BSP port is provide. Manually, we have to remove follower plate, spring, top cover and fill the grease from the top of the reservoir and to fit all the components by pressure . For air removing unscrew the bleed plug pull the handle maximum out and press the follower plate by knob till grease comes out from bleed plug. DISTRIBUTION SYSTEM A Progressive block is used to distribute the grease to the available lubrication points in sequence one after another. Progressive Blocks are added as per requirement.

Model Reservoir Cap Discharge Max. Pressure
KMGP-500-3 0.5 Kg 3 gms/stroke 70 Kg/cm square
KMGP-1000-4 1.0 Kg 4 gms/stroke 100 Kg/cm square
KMGP-1500-6 1.5 Kg 6 gms/stroke 120 Kg/cm square

Progressive Blocks

KRS introduce progressive distributor blocks of KPB-5000 / KPB-6000 series are meant for distribution of grease/oil delivered by a pump. From this progressive block we get lubricant in sequently one after another. Any one outlet is blocked then the progressive block will stop functioning. with suitable monitoring devices, this blockages is sensed and suitable warning is given to avoid running the machine without proper lubrication. These blocks can be used for intermittent / continuous lubrication. This block has three type of elements- 1. Starting block 2. Middle block 3. End block Each middle block has two outlet & min. 03 middle block are required in progressive block we can add other middle blocks as per requirement.

12 / 24 V DC Radial Lubricator

These pumps are driven by 24V. Battery or 24V.DC supply. Pump is suitable for applications where power supply is either by 24V.battery or 24V.DC it is normally used with progressive distributors. It comes with different reservoir volume capacity 3 to 7Liters. The pump can accommodate 1 to 3 nos. Pumping units. Discharge 0 to 0.25cc per stroke/ Element adjustable. Max. Pressure 100 Kg/Cm². APPLICATIONS Buses & trucks chassis, concrete pumps, excavators, injection molding machine, power presses, printing presses, ginning machine etc.

Plunger Pumps

Plunger pump is a compact pump that gives metered amount of lubricant in every stroke. We can adjust the discharge by adjusting screw. Output can very from 0.05cc to 0.25cc/stroke & delivery pressure 200 Kg/cm2 max. The stroke of the plunger remains always same. The mounting threads of the plunger is M22×1.5. Plunger pump is also available in 0.50cc/stroke, 1.00cc/stroke & 2.50cc/stroke (Non adjustable).

Pneumatic Grease Pump

KRS has designed and manufactured PNEUMATIC GREASE PUMP is meant for automatic feeding of grease to bearing and other moving part of the machines as for Textile machine, Packing machine, Furnaces, Bleeding machine, Rolling mill Presses and Hammer, Rubber Processing machines, Agriculture and Construction Machines, Earth moving Machines etc.

Models SM PnGP-1500-10 SM PnGP-3000-12 SM PnGP-5000-15
Reservoir Capicity 1.5 kg 3 Kg 5 Kg
Discharge / Stroke 0-10 grams (adjustable) 0-12 grams (Adjustable) 0-15 grams (adjustable)
Delivery Pressure Max. 150 Kg/cm Square 120 Kg/cm Square 100 kg/cm square
Input Pressure 5-7 Kg/Cm Square 5-7 Kg/cm Square 5-7Kg/Cm square